a. LAUNCH_ERR
- Userspace error.
- Triggered due to faulty launch.
- Handle using recovery to reset CE engine and teardown the
faulty channel.
b. An INVALID_CONFIG -
- Triggered when LCE is mapped to floorswept PCE.
- On iGPU, we use the default PCE 2 LCE HW mapping.
The default mapping can be read from NV_CE_PCE2LCE_CONFIG
INIT value in CE refmanual.
- NvGPU driver configures the mapping on dGPUs (currently only on
Turing).
- So, this interrupt can only be triggered if there is
kernel or HW error
- Recovery ( which is killing the context + engine reset) will
not help resolve this error.
- Trigger Quiesce as part of handling.
c. A MTHD_BUFFER_FAULT -
- NvGPU driver allocates fault buffers for all TSGs or contexts,
maps them in BAR2 VA space and writes the VA into channel
instance block.
- Can be triggered only due to kernel bug
- Recovery will not help, need quiesce
d. FBUF_CRC_FAIL
- Triggered when the CRC entry read from the method fault buffer
does not match the computed CRC from the methods contained in
the buffer.
- This indicates memory corruption and is a fatal interrupt which
at least requires the LCE to be reset before operations can
start again, if not the entire GPU.
- Better to quiesce on memory corruption
CE Engine reset (via recovery) will not help.
e. FBUF_MAGIC_CHK_FAIL
- Triggered when the MAGIC_NUM entry read from the method fault
buf does not match NV_CE_MTHD_BUFFER_GLOBAL_HDR_MAGIC_NUM_VAL
- This indicates memory corruption and is a fatal interrupt
- Better to quiesce on memory corruption
f. STALLING_DEBUG
- Only triggered with SW write for debug purposes
- Debug interrupt, currently ignored
Move launch error handling from GP10b to GV11b HAL as -
1. LAUNCHERR_REPORT errcode METHOD_BUFFER_ACCESS_FAULT is not
defined on Pascal
2. We do not support GP10b on dev-main ToT
JIRA NVGPU-8102
Change-Id: Idc84119bc23b5e85f3479fe62cc8720e98b627a5
Signed-off-by: Tejal Kudav <tkudav@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2678893
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
Below CE interrupts do not have any users(usecases) on safety build;
disable them only on safety build.
1. BLOCKPIPE stall intr: Not used by GFX(VKSC) and CUDA on safety.
2. NONBLOCK_PIPE nonstall intr: Non-stall intrs are not supported
on safety build. Also, this one is not used by GFX(VKSC)
and CUDA.
3. STALLING_DEBUG intr: Added in Orin tree. It is only needed for
debugging. Disable on safety build as there is no current
usage in driver.
4. POISON_ERROR intr: Poison is a fault containment and not
supported on GA10b.
5. INVALID_CONFIG intr: Floor sweeping not supported on functional
safety SKU.
Bug 3548082
Change-Id: I8d97ccb38f138b2c04a780e1c255a64d28723405
Signed-off-by: Tejal Kudav <tkudav@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2671927
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
Issue observed:
- In GA10B, it was observed that after recovery happens
ELPG does not engage.
- It was because, after CE reset, when nvgpu_submit_twod test
was run to engage ELPG, IDLE_FLIPPED_PWR_OFF signal was asserted.
- This means that when ELPG was engaged (engine is in PWR_OFF),
some idle signal flips (becomes non-idle) and this causes
IDLE_SNAP. After IDLE_SNAP is hit, ELPG will not engage further.
- After debugging from WAVES, it was observed that:
LCE0/LCE1 are not done with the reset sequence.
- The state of these LCE is RESET0. A pri request (pri read
to NV_CE_PCE_MAP register in CE) is seen that kicks it out of
RESET0. After this state, it goes through few states to update
some internal states (states RESET1/RESET2/PCE_MAP etc) and then
eventually settles down to IDLE state.
Solution:
- Read ce_pce_map_r register in recovery sequence (after ce reset).
- It is observed that when this read is added recovery is complete
and post that when nvgpu_submit_two test is executed, ELPG is engaging.
- This means that a pri read is needed after CE reset so that it settles
to idle state properly and post that ELPG can engage properly.
Bug 200734258
Change-Id: I5bb84921ca62a740fde81ffe6c29ccde4ebb341b
Signed-off-by: Divya Singhatwaria <dsinghatwari@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2554493
Reviewed-by: svcacv <svcacv@nvidia.com>
Reviewed-by: svc-mobile-coverity <svc-mobile-coverity@nvidia.com>
Reviewed-by: svc-mobile-misra <svc-mobile-misra@nvidia.com>
Reviewed-by: svc-mobile-cert <svc-mobile-cert@nvidia.com>
Reviewed-by: svc_kernel_abi <svc_kernel_abi@nvidia.com>
Reviewed-by: Mahantesh Kumbar <mkumbar@nvidia.com>
Reviewed-by: Seema Khowala <seemaj@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
GVS: Gerrit_Virtual_Submit
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
