Enable nvriscv debug buffer feature in NVGPU.
Debug buffer is a feature to print the debug log from ucode onto console
in real time.
Debug buffer feature uses the DMEM, queue and SWGEN1 interrupt to share
ucode debug data with NVGPU.
Ucode writes debug message to DMEM and updates offset in queue to trigger
interrupt to NVGPU.
NVGPU copies the debug message from DMEM to local buffer to process and
print onto console.
Debug buffer feature is added under falcon unit and required engine
can utilize the feature by providing required param through public
functions.
Currently GA10B NVRISCV NS/LS PMU ucode has support for this feature
and enabled support on NVGPU side by adding required changes, with this
feature enabled, it is now possible to see prints in real time.
JIRA NVGPU-6959
Change-Id: I9d46020470285b490b6bc876204f62698055b1ec
Signed-off-by: mkumbar <mkumbar@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2548951
Reviewed-by: svc-mobile-coverity <svc-mobile-coverity@nvidia.com>
Reviewed-by: svc-mobile-cert <svc-mobile-cert@nvidia.com>
Reviewed-by: svc-mobile-misra <svc-mobile-misra@nvidia.com>
Reviewed-by: svc_kernel_abi <svc_kernel_abi@nvidia.com>
Reviewed-by: Vijayakumar Subbu <vsubbu@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
GVS: Gerrit_Virtual_Submit
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Issue observed:
- In GA10B, it was observed that after recovery happens
ELPG does not engage.
- It was because, after CE reset, when nvgpu_submit_twod test
was run to engage ELPG, IDLE_FLIPPED_PWR_OFF signal was asserted.
- This means that when ELPG was engaged (engine is in PWR_OFF),
some idle signal flips (becomes non-idle) and this causes
IDLE_SNAP. After IDLE_SNAP is hit, ELPG will not engage further.
- After debugging from WAVES, it was observed that:
LCE0/LCE1 are not done with the reset sequence.
- The state of these LCE is RESET0. A pri request (pri read
to NV_CE_PCE_MAP register in CE) is seen that kicks it out of
RESET0. After this state, it goes through few states to update
some internal states (states RESET1/RESET2/PCE_MAP etc) and then
eventually settles down to IDLE state.
Solution:
- Read ce_pce_map_r register in recovery sequence (after ce reset).
- It is observed that when this read is added recovery is complete
and post that when nvgpu_submit_two test is executed, ELPG is engaging.
- This means that a pri read is needed after CE reset so that it settles
to idle state properly and post that ELPG can engage properly.
Bug 200734258
Change-Id: I5bb84921ca62a740fde81ffe6c29ccde4ebb341b
Signed-off-by: Divya Singhatwaria <dsinghatwari@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2554493
Reviewed-by: svcacv <svcacv@nvidia.com>
Reviewed-by: svc-mobile-coverity <svc-mobile-coverity@nvidia.com>
Reviewed-by: svc-mobile-misra <svc-mobile-misra@nvidia.com>
Reviewed-by: svc-mobile-cert <svc-mobile-cert@nvidia.com>
Reviewed-by: svc_kernel_abi <svc_kernel_abi@nvidia.com>
Reviewed-by: Mahantesh Kumbar <mkumbar@nvidia.com>
Reviewed-by: Seema Khowala <seemaj@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
GVS: Gerrit_Virtual_Submit
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
On all chips except ga10b, the number of ROP, L2 units per FBP
were in sync, hence, their FS masks could be represented by a single
fuse register NV_FUSE_STATUS_OPT_ROP_L2_FBP. However, on ga10b, the ROP
unit was moved out from FBP to GPC and it no longer matches the number
of L2 units, so the previous fuse register was broken into two -
NV_FUSE_CTRL_OPT_LTC_FBP, NV_FUSE_CTRL_OPT_ROP_GPC.
At present, the driver reads the NV_FUSE_CTRL_OPT_ROP_GPC register
and reports incorrect L2 mask. Introduce HAL function
ga10b_fuse_status_opt_l2_fbp to fix this.
In addition, rename fields and functions to exclusively fetch L2 masks,
this should help accommadate ga10b and future chips in which L2 and ROP units
are not in same. As part of this, the following functions and
fields have been renamed.
- nvgpu_fbp_get_rop_l2_en_mask => nvgpu_fbp_get_l2_en_mask
- fuse.fuse_status_opt_rop_l2_fbp => fuse.fuse_status_opt_l2_fbp
- nvgpu_fbp.fbp_rop_l2_en_mask => nvgpu_fbp.fbp_l2_en_mask
The HAL ga10b_fuse_status_opt_rop_gpc is removed as rop mask is not
used anywhere in the driver nor exposed to userspace.
Bug 200737717
Bug 200747149
Change-Id: If40fe7ecd1f47c23f7683369a60d8dd686590ca4
Signed-off-by: Antony Clince Alex <aalex@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2551998
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
This CL covers the following modifications,
1) Added logic to skip the graphics unit specific sw context load
register write during context creation when MIG is enabled.
2) Added logic to skip the graphics unit specific sw method
register write when MIG is enabled.
3) Added logic to skip the graphics unit specific slcg and blcg gr
register write when MIG is enabled.
4) Fixed some priv errors observed during MIG boot.
5) Added MIG Physical support for GPU count < 1.
6) Host clk register access is not allowed for GA100.
So skipped to access host clk register.
7) Added utiliy api - nvgpu_gr_exec_with_ret_for_all_instances()
8) Added gr_pri_mme_shadow_ram_index_nvclass_v() reg field
to identify the sw method class number.
Bug 200649233
Change-Id: Ie434226f007ee5df75a506fedeeb10c3d6e227a3
Signed-off-by: Lakshmanan M <lm@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2549811
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
Replace all nvgpu_next functions/structs either by 1) collapsing them
into nvgpu legacy functions/structs 2) renaming them as follows:
- nvgpu_next_*() => nvgpu_(ga10b/ga100)_*()
- nvgpu_next_*() => (ga10b/ga100)_*()
- nvgpu_next_*() => nvgpu_*() [only if this doesn't cause collision]
- nvgpu_next_*() = > nvgpu_*_extra()
Create hal.sim unit and move Ampere+ SIM code into it.
Jira NVGPU-4771
Change-Id: I215594a0d0df4bd663bd875a0d0db47bcb9ff6a2
Signed-off-by: Antony Clince Alex <aalex@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2548056
Reviewed-by: svc_kernel_abi <svc_kernel_abi@nvidia.com>
Reviewed-by: Mahantesh Kumbar <mkumbar@nvidia.com>
Reviewed-by: Vijayakumar Subbu <vsubbu@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
GVS: Gerrit_Virtual_Submit
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
