mirror of
git://nv-tegra.nvidia.com/device/hardware/nvidia/t23x-public-dts.git
synced 2025-12-22 09:12:02 +03:00
92a36dcc76
Enable WDR(wide dynamic range) mode for IMX390. 1 Add WDR mode table to IMX390 overlay. 2 Support only link A in desrializer (only one sensor is supported for now). Add tegra234-p3737-camera-imx390-addr-0x21-overlay.dtbo for IMX390 sensor with i2c address 0x21. Bug 4505240 Change-Id: I6ccff56d0943674bc2f0142c8829fb4c812569a1 Signed-off-by: Ankur Pawar <ankurp@nvidia.com> Reviewed-on: https://git-master.nvidia.com/r/c/device/hardware/nvidia/t23x-public-dts/+/3105263 Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com> Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
136 lines
3.2 KiB
Devicetree
136 lines
3.2 KiB
Devicetree
// SPDX-License-Identifier: GPL-2.0-only
|
|
// SPDX-FileCopyrightText: Copyright (c) 2018-2024, NVIDIA CORPORATION & AFFILIATES. All rights reserved.
|
|
|
|
/dts-v1/;
|
|
/plugin/;
|
|
|
|
#include <dt-bindings/clock/tegra234-clock.h>
|
|
#include <dt-bindings/gpio/tegra234-gpio.h>
|
|
#include <dt-bindings/tegra234-p3737-0000+p3701-0000.h>
|
|
|
|
#define CAM0_RST_L TEGRA234_MAIN_GPIO(H, 3)
|
|
|
|
/* camera control gpio definitions */
|
|
/ {
|
|
overlay-name = "Jetson Camera IMX390";
|
|
jetson-header-name = "Jetson AGX CSI Connector";
|
|
compatible = JETSON_COMPATIBLE;
|
|
|
|
fragment@0 {
|
|
target-path = "/";
|
|
|
|
__overlay__ {
|
|
tegra-capture-vi {
|
|
num-channels = <1>;
|
|
ports {
|
|
status = "okay";
|
|
port@0 {
|
|
status = "okay";
|
|
liimx390_vi_in0: endpoint {
|
|
status = "okay";
|
|
port-index = <0>;
|
|
bus-width = <4>;
|
|
remote-endpoint = <&liimx390_csi_out0>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
tegra-camera-platform {
|
|
modules {
|
|
status = "okay";
|
|
module0 {
|
|
badge = "imx390_rear";
|
|
position = "rear";
|
|
orientation = "1";
|
|
status = "okay";
|
|
drivernode0 {
|
|
status = "okay";
|
|
/* Declare PCL support driver (classically known as guid) */
|
|
pcl_id = "v4l2_sensor";
|
|
/* Declare the device-tree hierarchy to driver instance */
|
|
sysfs-device-tree = "/sys/firmware/devicetree/base/bus@0/i2c@3180000/tca9546@70/i2c@0/imx390_a@21";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
bus@0{
|
|
host1x@13e00000 {
|
|
nvcsi@15a00000 {
|
|
num-channels = <1>;
|
|
channel@0 {
|
|
status = "okay";
|
|
ports {
|
|
status = "okay";
|
|
port@0 {
|
|
status = "okay";
|
|
liimx390_csi_in0: endpoint@0 {
|
|
status = "okay";
|
|
port-index = <0>;
|
|
bus-width = <4>;
|
|
remote-endpoint = <&liimx390_imx390_out0>;
|
|
};
|
|
};
|
|
port@1 {
|
|
status = "okay";
|
|
liimx390_csi_out0: endpoint@1 {
|
|
status = "okay";
|
|
remote-endpoint = <&liimx390_vi_in0>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
i2c@3180000 {
|
|
tca9546@70 {
|
|
status = "okay";
|
|
compatible = "nxp,pca9546";
|
|
reg = <0x70>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
skip_mux_detect = "yes";
|
|
i2c@0 {
|
|
reg = <0>;
|
|
i2c-mux,deselect-on-exit;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
dser: max929x_a@64 {
|
|
compatible = "Maxim,max929x";
|
|
reg = <0x64>;
|
|
pwdn-gpios = <&gpio CAM0_RST_L GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
imx390_a@21 {
|
|
/* Define any required hw resources needed by driver */
|
|
/* ie. clocks, io pins, power sources */
|
|
clocks = <&bpmp TEGRA234_CLK_EXTPERIPH1>,
|
|
<&bpmp TEGRA234_CLK_EXTPERIPH1>;
|
|
clock-names = "extperiph1", "pllp_grtba";
|
|
mclk = "extperiph1";
|
|
channel = "a";
|
|
status = "okay";
|
|
reg = <0x1a>;
|
|
nvidia,gmsl-dser-device = <&dser>;
|
|
ports {
|
|
status = "okay";
|
|
port@0 {
|
|
status = "okay";
|
|
liimx390_imx390_out0: endpoint {
|
|
status = "okay";
|
|
port-index = <0>;
|
|
bus-width = <4>;
|
|
remote-endpoint = <&liimx390_csi_in0>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|