A kernel panic has been observed sometimes on reboot. The crash occurs
in the nvgpu_kernel_shutdown_notification() function when calling
nvgpu_cond_signal(). Fix this by checking that the 'gr' pointer is valid
before calling nvgpu_cond_signal().
Bug 3943885
Change-Id: I81e5e1b1128f22832daf01b880fac2a5e38f2a7a
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2846761
Reviewed-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-by: Alex Waterman <alexw@nvidia.com>
GVS: Gerrit_Virtual_Submit <buildbot_gerritrpt@nvidia.com>
nvpmodel updates the devfreq frequency limits as per power requirements
for specific chip. Clock arbiter ignored these limits and set clock
to maximum supported frequency which may lead to leaking power and
over heating.
Add support to get the devfreq limits by registering PM_QOS notifiers.
Note that with this patch we enable CONFIG_GK20A_PM_QOS when PM_DEVFREQ
is enabled. So it will be enabled for all supported kernels (4.9, 4.14
kernels continue to support this. For 5.10+ kernels notifiers added in
this patch will be used. Thermal framework related notifiers for kernels
after 4.14 will not be registered as those use downstream interfaces
that are not available.)
We maintain devfreq min/max limits in the scale profile and update those
in the notifier calls. We use these limits to clamp the frequency in the
clock arbiter.
Bug 3852824
Change-Id: I734a9fb080fee1a91e9b5da071b662dbd9a18682
Signed-off-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2822686
Tested-by: Rajkumar Kasirajan <rkasirajan@nvidia.com>
Reviewed-by: Rajesh Devaraj <rdevaraj@nvidia.com>
Reviewed-by: Dinesh T <dt@nvidia.com>
Reviewed-by: Rajkumar Kasirajan <rkasirajan@nvidia.com>
Reviewed-by: Ankur Kishore <ankkishore@nvidia.com>
GVS: Gerrit_Virtual_Submit <buildbot_gerritrpt@nvidia.com>
In the current setting, clock arbiter skips setting
the clock if its already set previously. The value
set by the arbiter is stored in
"struct nvgpu_clk_arb->actual" whenever the clock is
updated via the arbiter. However, DVFS might also
update the clock and the updates are not synchronized
with the arbiter. Hence, ensure that any clock
requests are always updated i.e. the requested rate is
set even if the previous rate remains the same.
In the devfreq scale() part, scale emc when clk_arb
is active and skip setting of clocks.
Note that this is cherry-pick from dev-main. Previously
merged cherry-pick is not complete.
Bug 3666615
Bug 3852824
Change-Id: I480a816434dcd59d18a287954a536fd7061c707c
Signed-off-by: Debarshi Dutta <ddutta@nvidia.com>
Signed-off-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2822685
Reviewed-by: Ankur Kishore <ankkishore@nvidia.com>
GVS: Gerrit_Virtual_Submit <buildbot_gerritrpt@nvidia.com>
- The pmu_pg_task thread remains alive in the background
during railgate and rail-ungate.
- During rail-ungate, the PG task thread starts again and
executes PG-related tasks.
- It comes in pmu_pg_init_powergating() and waits for GR
initialization. Here it waits for gr to be initialized.
- In parallel, the main GPU thread works on rmmod (from
gpu_module_reload test).
- By this time, the main gpu thread has started rmmod and
gr->initialized can be set to false, thus causing an uninterruptible
wait for pmu_pg_task thread.
- To solve this, wake gr wait wq in rmmod path when
NVGPU_DRIVER_IS_DYING and NVGPU_KERNEL_IS_DYING flgas are set.
Bug 3806514
Bug 3756912
Change-Id: Id78d92f30b75aba1aee22398cc86a3acebd50ef6
Signed-off-by: Divya <dsinghatwari@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2798003
(cherry picked from commit d9345065bcb6d9ff497c127fa4cd52077f4ecfa4)
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2819084
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
- With ELPG + RG enabled, gpu_module_reload test fails.
- This happens because the test tries to unload nvgpu.ko
module and then reload it. This all happens with RG enabled.
- During rmmod of nvgpu.ko module the code path taken is:
nvgpu_remove() -> nvgpu_quiesce() -> gk20a_pm_prepare_poweroff
-> nvgpu_prepare_poweroff -> pmu_destroy
- In this code path, NVGPU_DRIVER_IS_DYING flag is not set.
- Thus, in pmu_pg_task thread (which keeps on running in parallel),
commands are sent to the PMU and the driver keeps waiting for the
ACK in nvgpu_pmu_wait_fw_ack_status().
- Add nvgpu_start_gpu_idle() in nvgpu_remove() path, before calling
nvgpu_quiesce().
- This will set NVGPU_DRIVER_IS_DYING flag to true.
- nvgpu_can_busy() will return 0 when the driver is shutting down or
getting removed.
Bug 3676200
Bug 3756912
Change-Id: Ic24f58c210e4b477e5d560b053b70c16308e16f1
Signed-off-by: Divya <dsinghatwari@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2762310
(cherry picked from commit 8f1792565e71b822a6e9cc50af4b43c1b48518e0)
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2819082
Reviewed-by: Mahantesh Kumbar <mkumbar@nvidia.com>
GVS: Gerrit_Virtual_Submit <buildbot_gerritrpt@nvidia.com>
Error reportings were removed from the following functions in GV11B
1. gp10b_priv_ring_decode_error_code
2. gv11b_gr_intr_report_gpcmmu_ecc_err
3. gv11b_gr_intr_report_icache_uncorrected_err -> Duplicate
4. gv11b_gr_intr_report_l1_tag_corrected_err -> Duplicate
5. gv11b_gr_intr_report_l1_tag_uncorrected_err -> Duplicate
6. gv11b_ltc_intr_handle_dstg_ecc_interrupts
7. gv11b_ltc_intr_handle_ecc_sec_ded_interrupts
8. gv11b_ltc_intr_handle_tstg_ecc_interrupts
9. gv11b_pbdma_handle_intr_1
The ones marked "Duplicate" are the only ones which are used for both
gv11b and ga10b. Others are invoked only for gv11b and not ga10b.
a) For gv11b_gr_intr_report_l1_tag_corrected_err and
gv11b_gr_intr_report_l1_tag_corrected_err, the errors are handled by moving
them into gv11b_gr_intr_set_l1_tag_corrected_err and
gv11b_gr_intr_set_l1_tag_uncorrected_err functions respectively. These
functions are invoked only from GV11B.
b) For gv11b_gr_intr_report_icache_uncorrected_err, the errors are
handled by adding them in gv11b_set_icache_ecc_status_uncorrected_errors
which is specific to gv11b.
Bug 200588528
Signed-off-by: Debarshi Dutta <ddutta@nvidia.com>
Change-Id: I581bdfec8f996643d6af63b2b80a135e7d715b89
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2770836
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
GVS: Gerrit_Virtual_Submit <buildbot_gerritrpt@nvidia.com>
- nvpmodel service used to expect a return value of -ENODEV from the
underlying tpc_pg_mask_store() when the golden image size was
initialized.
- With the current implementation, the return value is -EINVAL due to
which write for new tpc_pg_mask was not successful.
- Update the return value to -EBUSY for the case where golden image
is already initialized.
Bug 3765637
Change-Id: I5a1a38cce035ea245db5d72c9f5db210d3bb95f1
Signed-off-by: Divya <dsinghatwari@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2778855
Reviewed-by: svcacv <svcacv@nvidia.com>
Reviewed-by: Mahantesh Kumbar <mkumbar@nvidia.com>
GVS: Gerrit_Virtual_Submit <buildbot_gerritrpt@nvidia.com>
There are 2 issues here:
1. top_en register is being masked for each leaf level
interrupt disable operation. top_en bit should be disabled
as part of top level stall operation only.
2. Wrong mask is being calculated to disable the leaf_en bits
for a unit which inturn affects the entire subtree.
Subtree_mask_restore for a subtree stores the last state
of interrupts that are enabled. As part of disable operation,
we only need to update subtree_mask_restore and not reupdate
subtree_mask for that subtree. Same logic applies to enable
operation.
Renamed the apis to better reflect their operation. The
interrupt disabling is done at unit level and not subtree level.
Bug 3712884
Change-Id: Id840c77f612021a303cfe0e8dca69386bc570273
Signed-off-by: Kishan <kpalankar@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2752541
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2758138
Reviewed-by: Tejal Kudav <tkudav@nvidia.com>
Reviewed-by: Vaibhav Kachore <vkachore@nvidia.com>
GVS: Gerrit_Virtual_Submit
The present implementation of podgov driver doesn't
export any symbols and as a result, the dependency
between NVGPU driver and podgov is not established
by depmod. Fix that by adding a soft dependency.
MODULE_SOFTDEP("pre: governor_pod_scaling");
This allows loading the podgov governor before
nvgpu driver.
Bug 3674235
Signed-off-by: Debarshi Dutta <ddutta@nvidia.com>
Change-Id: Id1959639399042f488cdaa30372feb65d8f21aaa
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2740446
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
There are some configs which are set for the stable kernel and
it is identified from the NV_BUILD_KERNEL_OPTIONS.
The stable kernel build nvgpu as out-of-tree module and
pass the environment config CONFIG_TEGRA_OOT_MODULE during
build.
Hence, it is not required to use the NV_BUILD_KERNEL_OPTIONS to
identify the kstable build. It uses CONFIG_TEGRA_OOT_MODULE for
setting the configs for build as module.
Bug 3652905
Change-Id: I6570760e91ca98a4c83d7691fad517b2c772e629
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2720729
(cherry picked from commit 646a48ea5a)
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2728409
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
On host copy engine PBDMA interrupt, channel is aborted as part of the
recovery and its syncpt value is set to the max threshold.
Syncpoint may then get incremented by PBDMA (incr cmd gets processed)
after this interrupt is handled leading to syncpoint value becoming
greater than the max threshold.
Again while unbinding the channel, syncpoint value is incremented until
it reaches max threshold. Since syncpoint value is already greater than
max threshold, host1x version of nvgpu_nvhost_syncpt_set_minval will
loop for entire u32 range until it reaches max threshold and this
will hang the channel unbind.
nvgpu_nvhost_syncpt_set_minval can ensure the syncpoint value is greater
than or equal to max threshold. Hence update the check for syncpoint
value from not equal to less than.
Bug 3681100
Change-Id: I96e7a1f53d4037e9ed858a2e90dd5a8d17ed6bb0
Signed-off-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2742604
Reviewed-by: Debarshi Dutta <ddutta@nvidia.com>
Reviewed-by: Vijayakumar Subbu <vsubbu@nvidia.com>
GVS: Gerrit_Virtual_Submit
Enable/disable LSPMU interrupt in MC, as required LSPMU
interrupts are configured as part of LSPMU ucode init and
don't need any additional PMU IRQ register to set/clear as
part of GPU power-on/off sequence.
Bug 3681561
Change-Id: Ifb47bc9cc83e16e46649b0eef5f257acb02f302c
Signed-off-by: mkumbar <mkumbar@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2740623
Reviewed-by: svcacv <svcacv@nvidia.com>
Reviewed-by: Vijayakumar Subbu <vsubbu@nvidia.com>
GVS: Gerrit_Virtual_Submit
Add error reporting support for T194's L1SS safety
services for linux.
Used GA10B's LUT for GV11B. The error ids for T194 are
different compared to GA10B. This is handled by creating
a separate table mapping existing error ids to match GV11B.
Ids that are not used by GV11B are set to U32_MAX to indicate
the driver to not send them to the l1ss driver.
Bug 200588528
Signed-off-by: Debarshi Dutta <ddutta@nvidia.com>
Change-Id: I10a267942df77458c3deee0aad1179955490aa74
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2736772
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
bpmp will floorsweep GPCs as per parameters to tpc_pg_mask sysfs.
While doing that corresponding GPC clocks are also disabled.
nvgpu should re-initialize the clocks every time the
GPC/TPC pg_masks are passed to bpmp mrq.
Also print error when clk_prepare_enable fails.
Introduce platform->clks_lock to protect access to platform->clks
and platform->num_clks done from unrailgate/railgate and bpmp
mrq set calls from sysfs.
Acquire static_pg_lock in railgate path to synchronize railgate
with sysfs.
Bug 3688506
Change-Id: I3203d78b87289e7a847d78b3117e2d3119be3425
Signed-off-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2738920
Reviewed-by: Amulya Yarlagadda <ayarlagadda@nvidia.com>
GVS: Gerrit_Virtual_Submit
To build nvgpu as external module NV_BUILD_KERNEL_OPTIONS dependency is
present to set the config CONFIG_NVGPU_NVMAP_NEXT.
Remove that dependency as rel-35 does not support kernels prior
to v5.10.
And nvlink symbols are not found while building with public sources.
nvlink is not supported on rel-35, hence disable that config.
Bug 3700823
Bug 3684625
Change-Id: I8787ecb9746dd010a025e6d53679d2f23578ad56
Signed-off-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2738479
Tested-by: Debarshi Dutta <ddutta@nvidia.com>
Reviewed-by: Debarshi Dutta <ddutta@nvidia.com>
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
GVS: Gerrit_Virtual_Submit
When destroying a virtual memory pool the associated page size must
be set in the nvgpu_vm_remap_op structure.
This patch adds a new nvgpu_vm_remap_page_size_flag() routine that
converts the page size derived from the vm/vm_area structs to the
corresponding NVGPU_VM_REMAP_OP_FLAGS_PAGESIZE bit.
Bug 3669908
Change-Id: Idca77cc36d353777b399c872f68a1f5231ddb8dd
Signed-off-by: Scott Long <scottl@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2734822
Tested-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-by: Vijayakumar Subbu <vsubbu@nvidia.com>
GVS: Gerrit_Virtual_Submit
- These unit tests are failing and we are going to take care of
unit tests as part of Safety work on dev-main.
It should not be an issue for rel-35.
Bug 3681100
Change-Id: I6f0f4d1697151b189c4f26e5206d25537e65a7bd
Signed-off-by: srajum <srajum@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2735815
GVS: Gerrit_Virtual_Submit
Reviewed-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-by: Vaibhav Kachore <vkachore@nvidia.com>
Enable DEVFREQ for OOT module unconditionally as the podgov governor
module.
linux/pm_qos is only used for downstream supported modifications
which is currently determined by CONFIG_GK20A_PM_QOS.
struct devfreq_dev_status doesn't have any field 'busy' in the upstream
driver hence enable it only for when downstream driver is in use
activated by CONFIG_GK20A_PM_QOS.
governor.h is only needed for android platforms which depend on 4.9
version of the kernel in downstream builds. Hence, added an compile
time flag to remove it for kernels versions greater than 4.9.
Jira LS-418
Signed-off-by: Debarshi Dutta <ddutta@nvidia.com>
Change-Id: Id242bd28e66ed187208f0d7975ee0bc508730a88
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2705766
(cherry picked from commit e81d0e8ff8)
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2734112
Reviewed-by: Jonathan Hunter <jonathanh@nvidia.com>
Reviewed-by: Vijayakumar Subbu <vsubbu@nvidia.com>
GVS: Gerrit_Virtual_Submit
In the current setting, clock arbiter skips setting
the clock if its already set previously. The value
set by the arbiter is stored in
"struct nvgpu_clk_arb->actual" whenever the clock is
updated via the arbiter. However, DVFS might also
update the clock and the updates are not synchronized
with the arbiter. Hence, ensure that any clock
requests are always updated i.e. the requested rate is
set even if the previous rate remains the same.
Bug 3666615
Signed-off-by: Debarshi Dutta <ddutta@nvidia.com>
Change-Id: I32bf4dbf81b19fdd6fa0bdec3a6c9a9312b78eca
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2732364
Reviewed-by: svcacv <svcacv@nvidia.com>
Reviewed-by: Vijayakumar Subbu <vsubbu@nvidia.com>
GVS: Gerrit_Virtual_Submit
To be able to access the full physical memory range, gpu's dma_mask
needs to be set to the max value of H/W compatible range.
For example. In order to support from 2GB to 66 GB, GV11B's dma_mask
needs to be atleast 37 bits. Set GV11B's dma_mask to 38 bit
and T23X's dma_mask to 39 bit. These values are supported by H/W.
Bug 3656729
Signed-off-by: Debarshi Dutta <ddutta@nvidia.com>
Change-Id: Icfff3c36a8c9cf074a254fa773c42e18020ae5de
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2723640
(cherry picked from commit 1bf9309f17)
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2724566
Reviewed-by: Brad Griffis <bgriffis@nvidia.com>
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
GVS: Gerrit_Virtual_Submit
Tested-by: Brad Griffis <bgriffis@nvidia.com>
nvgpu_device_get can return NULL if supplied invalid ID or instance
ID. We expect GR device struct to be non-NULL there hence just
assert that it is indeed non-NULL in gr_reset_engine and
ga10b_grmgr_init_gr_manager.
CID 224133
CID 250232
Bug 3512546
Change-Id: Id09a1c436a8e49b921111b940d3d013bd66bff7a
Signed-off-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2707018
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
As per Safety_Services, a client must perform polling to ensure that the
previously reported errors are cleared at FSI, in case of back-to-back
error reporting. However, to minimize the polling overhead, NvGPU driver
performs polling only when the error to be reported is corrected error
to ensure that it is not overwriting the previously reported
uncorrected/corrected error. In case of uncorrected errors, it will be
reported without doing polling. This situation leads to a failure in
error reporting, when uncorrected errors are reported back-to-back. This
is acceptable for safety builds where SW quiesce will be triggered
immediately after the reporting of first uncorrected error. In case of
other build configurations, MCU/SEH takes the decision on encountering
uncorrected errors. To handle such build configurations, polling is
enabled for all types of errors, in all build configurations.
This patch also removes an unused macro "ERR_TYPE_MASK".
Bug 3622420
Change-Id: I750b0406faec9b229d8d0c74e986807234362cb9
Signed-off-by: Rajesh Devaraj <rdevaraj@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2707105
Reviewed-by: Tejal Kudav <tkudav@nvidia.com>
Reviewed-by: Vaibhav Kachore <vkachore@nvidia.com>
GVS: Gerrit_Virtual_Submit
There shouldn't be an usecase that an fd, installed by nvgpu,
must be shared on exec with the new process. This doesn't only
lead to excessive number of fds in the exec process, but also
can lead to potential security issues.
This patch marks the fds with O_CLOEXEC, so that they get
closed on exec.
Bug 3583628
Change-Id: I3499b1429ac512b2c172e9e628d0a7a1417d72e3
Signed-off-by: Martin Radev <mradev@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2704350
Reviewed-by: svc-mobile-coverity <svc-mobile-coverity@nvidia.com>
Reviewed-by: svc-mobile-cert <svc-mobile-cert@nvidia.com>
Reviewed-by: Sagar Kamble <skamble@nvidia.com>
Reviewed-by: Konsta Holtta <kholtta@nvidia.com>
Reviewed-by: Alex Waterman <alexw@nvidia.com>
GVS: Gerrit_Virtual_Submit
The emulate mode support is determined after chip detect and is flagged
by using NVGPU_SUPPORT_EMULATE_MODE flag. The present logic prevents
user from configuring the emulate mode sysfs knobs if this flag is not
set, however the emulate mode usecase requires the user to configure the
syfs knob prior to power-on, hence defer emulate mode check to a later
stage after chip detect.
Bug 3621460
Change-Id: If522527542fa8d7e95ccbcff43b74adbb9e976e6
Signed-off-by: Antony Clince Alex <aalex@nvidia.com>
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2703953
Reviewed-by: svcacv <svcacv@nvidia.com>
Reviewed-by: svc-mobile-coverity <svc-mobile-coverity@nvidia.com>
Reviewed-by: svc-mobile-cert <svc-mobile-cert@nvidia.com>
Reviewed-by: Mayur Poojary <mpoojary@nvidia.com>
Reviewed-by: Mahantesh Kumbar <mkumbar@nvidia.com>
Reviewed-by: Ankur Kishore <ankkishore@nvidia.com>
GVS: Gerrit_Virtual_Submit
Tested-by: David Li <davli@nvidia.com>
Fix following Coverity defect:
cde.c : Unintentional integer overflow
The Coverity issue suggests that (u64) (nvgpu_ltc_get_ltc_count(g) * nvgpu_ltc_get_slices_per_ltc(g) * nvgpu_ltc_get_cacheline_size(g)) can cause overflow because typecasting is done after multiplication.
This patch solves that issue by typecasting it before multiplication.
CID 10112360
Bug 3460991
Signed-off-by: Jinesh Parakh <jparakh@nvidia.com>
Change-Id: I314ca7a9adc95fcb09f15eb603b56ad03ce34b99
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2697027
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
Fixed following Coverity Defects:
ioctl_as.c : Bad bit shift operation
mc_tu104.c : Bad bit shift operation
vm.c : Bad bit shift operation
vm_remap.c : Bad bit shift operation
A new linux header file for ilog2 is created.
The files which used the old ilog2 function
have been changed to use the new nvgpu_ilog2
function.
CID 9847922
CID 9869507
CID 9859508
CID 10112314
CID 10127813
CID 10127899
CID 10128004
Signed-off-by: Jinesh Parakh <jparakh@nvidia.com>
Change-Id: Ia201eea7cc426c3d6581e1e5ae3b882dbab3b490
Reviewed-on: https://git-master.nvidia.com/r/c/linux-nvgpu/+/2700994
Tested-by: mobile promotions <svcmobile_promotions@nvidia.com>
Reviewed-by: mobile promotions <svcmobile_promotions@nvidia.com>
